PRODUCT DETAILS
▲The main material requirements are high-strength aluminum alloy profiles, not less than 6063, and the processing grade reaches T5 standard. The overall fully enclosed design, no sharp angle on the surface, no screw exposure, imported powder coating surface treatment
▲The horizontal cross arm of the pendant tower has a safety bearing device, and the pendant tower has a central shaft rotating device
▲The inside of the pendant tower adopts a gas-electricity separation design to ensure the safety of use: the bottom end of the pendant box must have an oxygen drainage hole design to prevent the accumulation of oxygen in the tower and the power line caused by fire accidents.
▲ Through the static force load test, the cantilever angle is relative to the horizontal under the load state
▲ Gas terminal All gas sockets and joints are produced by the original factory, the terminal has passed antibacterial (E. coli) detection, gas sockets are identified as different colors and different shapes, with anti-misinsertion function, and have Standby (in-place to be connected) function, socket plug can ensure more than 20,000 times of plugging and unplugging, can be repaired with gas.
▲The power socket is AC 220V and has a separate grounding wire, the socket needs to have an equipotential grounding terminal, the grounding wire shall not be shared with the grounding of the pendant, and communication interfaces, video interfaces, network interfaces and other equipment can be installed as needed.
▲The tower bearing adopts needle roller type, and the number of rotations is not less than 100,000 times.
★ The maximum carrying capacity of the pendant tower ≥ 680Kg
★ The pendant tower has a four-fold load-bearing factor safety load device.
1. The rotation angle of the boom (including the boom column) is not less than 340°, and the six-point damping brake system has adjustable resistance.
2. Pallet carrying weight≥ 80kg; Pallet with drawer carrying weight≥ 50kg; Drawer carrying capacity≥ 20kg.
3. Frame type pendant cross arm rotation angle≥ 340º, length ≥ 850mm, width ≥ 190mm, height ≥ 125mm, wall thickness ≥ 10mm;
4. The length of the frame box beam is 650mm, the width of the beam is 165mm, and the height of the beam is 110mm; The oval profile support frame on both sides of the built-in power supply is 120mm long, 53mm wide and 860mm high. The inner diameter of the pallet slide is 70mm, and the distance between the two frames is 440mm.
5. The length of the hanging pipe connected to the tower box can be customized according to the height of the room, the diameter is ≥ 100mm, and the wall thickness is ≥4mm;
6. Pendant frame box rotation ≥ 340º, height ≥ 900mm.
7. Equipped with 1 set of rotatable extension infusion rack, rotating arm ≥ 350mm.
8. Box tray: 4pcs, pendant tray is eight-cavity aluminum alloy integrated die-casting molding; The length of the pallet with side rails ≥ 515mm, width ≥400mm, thickness ≥ 25mm;
9. Drawer: 1pc, carrying weight≥ 20Kg. Drawer inner diameter ≥ 320mm, width ≥ 240mm, height ≥ 120mm, pull-out length ≥ 20mm; Drawer outer diameter size≥ length 430mm, width ≥ 300mm, height ≥ 160mm; Drawer with automatic suction design;
▲Each set of configuration air source: oxygen * 2pcs, negative pressure suction * 2pcs, compressed air * 1pc, carbon dioxide * 1pc; Optional negative pressure suction device and oxygen inhaler
▲Each set of configuration power sockets ≥ 6 (compatible with national, American and British standards), with *3 power supplies on both sides of the frame;
▲Grounding terminal *2pcs; The configuration can be upgraded and can be flexibly selected according to user requirements.
Standard configuration:
Base * 1 set、Shield * 1 pc、Crossarm * 1 set、Pipes * 1 set、Box * 1 set、Pallet * 4 pcs、Drawer* 1 pc、Infusion rack * 1 pc、Oxygen * 2 pcs、Negative pressure suction * 2 pcs、Compressed air * 1 pc、
Carbon dioxide* 1 pc、Sockets * 6 pcs、Grounding terminal * 2 pcs、Network cable interface * 1 pc、Manufacturer qualification information *1 set
