WME-D7900C Electric heavy type double arm medical pendant(anesthesia)

▲The main material requirements are high-strength aluminum alloy profiles, and the processing grade reaches T5 standard. The overall fully enclosed design, no sharp angle on the surface, no exposed screws;

▲The horizontal cross arm of the pendant tower has a safety bearing device, and the pendant tower has a central shaft rotating device

▲The inside of the pendant tower adopts a gas-electricity separation design to ensure the safety of use: the bottom end of the pendant box must have an oxygen drainage hole design to prevent the accumulation of oxygen in the tower and the power line caused by fire accidents

▲ Gas terminal All gas sockets and joints are produced by the original factory, the terminal has passed antibacterial (E. coli) detection, gas sockets are identified as different colors and different shapes, with anti-misinsertion function, and have Standby (in-place to be connected) function, socket plug can ensure more than 20,000 times of plugging and unplugging, can be repaired with gas.

▲The power socket is AC 220V and has a separate grounding wire, the socket needs to have an equipotential grounding terminal, the grounding wire shall not be shared with the grounding of the pendant, and communication interfaces, video interfaces, network interfaces and other equipment can be installed as needed.

★ The pendant tower has a four-fold load-bearing factor safety load device

1. The rotation angle of the boom (including the boom column) is not less than 340°, and the six-point damping brake system has adjustable resistance

2. Working power: AC220V, 50Hz; Input power: 6KVA;

3. The length of the middle shaft of the pendant tower ≥ 180mm, and the diameter ≥ 110mm; Wall thickness≥ 17mm;

4. The length of the hanging pipe connected to the tower box can be customized according to the height of the room, the diameter is ≥ 100mm, and the wall thickness is ≥ 4mm; Height≥ 800mm;

5. The length of the pendant tower cross arm ≥ 850mm+700mm, width ≥ 190mm, height ≥ 125mm, wall thickness ≥ 12mm; CAN ELECTRIC LIFT 400MM;

6. The box body rotates ≥ 340º, the diamond-shaped box has no angular design, the left and right sides of the box body are equipped with a stainless steel infusion pump bracket, the syringe pump frame is fixed up and down, the upper section is a four-section pagoda-shaped, and the lower section is a spiral fixed structure.

7. The center distance between the infusion pump brackets on both sides is ≥ 500mm, and 6 infusion pump syringe pumps of different specifications can be hung ≥.

8. Instrument platform: 2 layers (bearing weight≥ 50Kg, height adjustable), tray thickness 230mm, length ≥ 440mm, width ≥ 430mm, length (including side rail size) ≥ 510mm, stainless steel side rails on both sides ≥ length 350mm, width ≥ 10mm, height ≥ 20mm, optional hanging net basket, etc

9. The pallet fixing method adopts reinforced aluminum alloy tripod support, the length of the tripod is ≥ 155mm, and the thickness is ≥7mm

10. Drawer: 1pc, carrying weight≥ 20Kg. Drawer inner diameter ≥ 40mm, width ≥ 270mm, height ≥ 70mm, drawer with automatic suction design;

▲Gas terminal standard configuration: oxygen * 2pcs, negative pressure suction * 1pc, compressed air * 1pc, anesthesia waste emission * 1pc; Optional

negative pressure suction device and oxygen inhaler

1. Power sockets: 6pcs, 220V, 10A (compatible with international plugs);

2. Grounding terminal: 2pcs; Network interface: RJ45, 1pc;

Standard configuration:

Base *1 set、 Shield *1 pc、 Crossarm *2 sets、 Pipe*1 set、 Box *1 set、 Tray * 2 pcs、 Drawer *1 pc、 Infusion rack *1 pc、 Oxygen * 2 pcs、 Negative pressure attraction * 1 pc、 Compressed air *1 pc、

Anesthesia waste discharge *1 pc、 Sockets *6 pcs、 Grounding terminal *2 pcs、 Network cable interface *1 pc、 Manufacturer qualification information *1 set